How to Repair Bifold Door Top Roller Guide

If your bifold doors are sticking then it's likely that they need some attention. It is possible that you need to clean, lubricate or adjust them. The issue could be caused by loose screws on the top pivot or by the top guide roller.

This kit contains all the hardware needed to return your bi-fold door repairs near me closet door system to optimal performance.

Remove the Door

Installing an internal set of bifold doors could seem like a complex and difficult project however, it's actually easy for DIYers with a few years of experience. The frame is not the problem however getting the doors to fold and close smoothly is. Because bifold doors are intricate machines, they might require some tweaking to ensure they are working properly. This could be as easy as tightening a screw or as complex as removing the door and replacing the pivot pin or roller.

You can usually fix these problems with a few simple adjustments, without the need to take off the doors. You might notice that your bifold doors are sliding or scraping the floor, or jumping out of track. It's not difficult to fix these issues. Follow three easy steps and your bifold doors will be back on the right direction in short time.

One of the most common issues that internal bifold doors have to face is the tendency to slide out of alignment. This could be due to loose screws, holes in the anchor/pivots, or a misaligned bifold door repairs near me door. Most times, this can be corrected with a few simple adjustments. If, however, your door doesn't move at all, you may have to replace it.

You'll need to open the door with an screwdriver, and perhaps a pair pliers to loosen any pivot pins that are too tight. The screwdriver is used to release the locking levers at the bottom bracket for pivots. The pliers are used for removing the pin.

Once the top roller has become loose it should be possible to lift the door and then swivel it downward and allow you to pull it off of its track and pivot brackets. It's usually a straightforward procedure, but be cautious not to let the door strike the frame of the door. Then, you can sand down the edges of the door to smooth it. You can then paint or refinish the door as required.

Remove the Roller Guide

This spring-loaded guide roller is mounted on the top of the bifold door to assist with smooth operation. It is designed to work with Kenna frames and can fit doors that are 1 to 1-3/8 inches thick. It is made from steel, nylon and plastic components. It can be used to replace a worn-out or damaged guide.

To begin removing the guide for the roller, remove the screws that hold it in place by using the screwdriver and a little to loosen it. Use your hands to slowly pull it from the frame. It may take some effort, so you should have an assistant help you keep the door in place while you remove it.

Once the old guide is removed, carefully cut through the remaining finish around the foot of the new guide using the help of a razor blade to remove it from the rod blank. This will make it easier to remove and will prevent damage to the new guide foot. The guide foot is extremely sharp, and it can cut or snag fingers.

It is possible to use some force to remove the guide, but be careful not to break or chip the foot. After you've removed the guide that was previously attached, take out any threads or epoxy left in the place where it was attached. This will avoid future issues with the guide.

After removing the old guide, you can test your replacement by placing it in its place and then applying a few rotations of masking tape or another form of guide tubing to keep it in its place. This allows you to double-check the guide alignment and spacing to make sure everything is properly set up. Whether you're eye-balling it or using the always accurate CRB Spine Finder and Deflection System This step is crucial to avoid any problems in the future.

The last step is to replace the door. If the guide is in the correct position and functioning in the correct way, then you can proceed. Make sure to replace and tighten any screws or pins you removed or loosen.

Remove the Bottom Pivot

Bifold doors are a stunning addition to any home but sometimes they require some tweaking or adjustment to stay in good shape. Certain issues can be solved with the doors in place. Others will require that the doors be removed. This guide will demonstrate how to take off the internal bifold door repair bracket door pins, rollers and pivots.

Gathering your tools is the first step. Getting everything together before time can save you some frustration later in the process. You'll need a screwdriver pliers and perhaps a wrench. A set of basic tools can be purchased at a reasonable price from a local hardware store. Keep a supply of wood glue in your kit. This will come in handy if you have to glue one of the rollers back in the correct position.

Once you've collected your tools, start by opening the bifold doors. Then, you'll need to loosening the top track bracket with your screwdriver. Once this is loose, the door should be free to slide off the top track completely. It might take a bit of dancing to get it there, but it should come off the track.

The pivot on the bottom of the frame will need to be removed. Close all doors to the interior prior to starting. This will be much easier than trying to work from the inside. If the track on the bottom is still in good condition it will be possible to just lift up the door and then remove the track.

If the track is damaged, you'll have to replace it. You can get replacement tracks for both bifold doors as well as swinging closet doors from your local hardware store. If the track is badly damaged then you may need to replace it entirely.

After your track has been repaired or replaced it is time to test the doors to ensure their proper operation. Make sure they're capable of moving smoothly in and out of position. You'll want to ensure that the edges of your door are aligned to the frame when closed. If they're not, you'll need to adjust the top pivot bracket by tightening or loosening the bottom set screw.

Replace the Roller

Bifold doors neatly enclose closets as well as laundry nooks and pantries, but only when they function correctly. They are made up of two panels that hinge together and slide open on tracks that are positioned in the top of the frame. Over time, the roller guide bearings can wear out, causing the doors to sag and scrape against the floor. The guide roller can be replaced in just a few minutes using a few tools.

The first step is to take the guide for the roller from the door panel. The bottom pivot bolt must be removed, and the screw that connects the guide to the top of the door panel should be loosened. After removing the guide, lift the panel off the track. Then, using a wrench, remove the top pivot bolt from the hole in the header of the frame by loosening the nut.

A top nylon replacement guide with a 7/8 inch diameter wheel and a base made of steel is available from Stanley, Cox or Acme. It mounts on the top edge of the repair bifold door top roller door, which is 1 to 1-3/8 inches in thickness and comes spring-loaded to self-adjust in the upper track for smooth glide.

A bifold door can also scratch against the floor when it closes and opens. This is often the result of adding carpet or other flooring materials that require the doors to be raised slightly to allow for adequate clearance. This issue can be resolved by removing the screws that adjust the bottom pivot and loosening the top track mounting screws, and moving anchor/pivot.

A new set of top roller guides is an inexpensive solution to a problem that can make bifold doors difficult to operate. They are usually available at your local hardware store in the door section. However they can also be purchased online from various vendors. You will also need an elongated squeeze-clamp as well as a small container of Elmer's wood adhesive which can be found in large box stores. The clamp is used to keep the area being repaired closed tightly after the glue has been installed and dried.